Answer any seven out of ten. દશમ ાથી કોઇપણ સ તન જવ બ આપો. 1. State forms of Potential energy. ૧. પૉટનશશયલ ઉરજાન સવરપ જણ વો. 2. State the Primary and Secondary sources of energy. ૨. પર થશમક અન દરિશતય ઉરજાન સવરપ જણ વો. 3. State methods of performance evaluation of boiler system. ૩. બોઇલર ક મગીરીન મલય કન કરવ મ ટની રીત જણ વો. 4. Explain the function of steam trap. ૪. સટીમ ટરપન ક યા સમરજવો . 5. Name the parameters on which heat loss through furnace walls depends. ૫. ભઠઠીની દરદવ લોમ થી થતો હીટ લોસ કય પર મીટર પર આધ રીત છ? 6. Which are the places in the furnace where stock cannot be placed? ૬. કઇ જગય એ ભઠઠીમ સટોકન મકી શક ય નહી? 7. Define specific power and volumetric efficiency of a compressor. ૭. કમપપરશર મ ટ સપસીફીક પ વર અન વોલયમદરટરક એદરફસીયાસીની વય ખય આપો. 8. Define effectiveness and heat duty of the heat exchanger. ૮. હીટ એકષચનજર મ ટ ઇફકટીવનસ અન હીટ ડયટીની વય ખય લખો 9. Show the relation between COP, EER and kw/ton indicators used to show the energy efficiency of Refrigeration system. ૯. COP, EER and kW/ton વચચનો સાબાધ જણ વો 10. Write short note on effect of heat exchanger surface maintenance on power consumption of Refrigeration system. ૧૦. રફરીજરટર શસસટમન પ વર વપર શ પર હીટ એકષચનજર સપ ટીન મનટનનસની અસર ટાકમ લખો.
State advantage and Disadvantage of Direct Method for boiler. પરશન. ર (અ) બોઇલરની પરતયકષ રીતન ફ યદ અન ગરફ યદ જણ વો.
[3 marks]State properties and characteristics of Fuel. (અ) બળતણની પરોપટી અન લ કષશણકત જણ વો.
[3 marks]Explain Bucket or Float type steam Trap (બ) બકટ અથવ ફલોટ ટ ઇપ સટીમ ટરપ સમરજવો.
[3 marks]1/4
[ marks]Write short note on energy saving in steam distribution system. (બ) વર ળ વહચણી શસસટમમ ઉરજ ાબચ વ પર ટક નોધ લખો. © Explain the control of furnace draught. (ક) ભઠઠીડર ફટન શનયાતરણ સમરજવો.
[4 marks]© Explain Forging Furnace. (ક) ફોરજાગ ભઠઠી સમરજવો.
[4 marks]Explain how furnace energy efficiency is increased by preventing heat loss from furnace opening. (ડ) ભઠઠીમ રહલ ખલલ ભ ગન લીધ થતો હીટ વયય અટક વત ભઠઠીની ક યાકષમત કવી રીત વધ રી શક ય ત સમરજવો
[4 marks]Explain point of increasing furnace efficiency using ceramic coating. (ડ) સીર શમક કોટીગ વ પરીન ભઠઠીની ક યાકષમત કવી રીત વધ રી શક ય તન મદદ સમરજવો.
[4 marks]Write steps of conservation of enegy in Industrial use. પરશન. 3 (અ) ઓધૌશગક વપર શમ ઉરજ ાબચ વન પગલ લખો.
[3 marks]Explain Topping and Bottoming cycle with steam turbine. (અ) ટોપીગ અન બોટોમીગ સ યકલ સટીમ ટરબ ઇન સ થ સમરજવો.
[3 marks]Explain for Heat exchanger (1) Fouling factor (2) LMTD correction factor. (બ) હીટ એકષચનજર મ ટ (1) ફોલીગ ફકટર (2) LMTD કરકશન ફકટર સમરજવો.
[3 marks]Classify heat exchanger and state the characteristics of an efficient heat exchanger. (બ) હીટ એકષચનજર વગીકરણ કરો અન ક યાકષમ હીટ એકષચનજરની લ કષશણકત લખો.
[3 marks]An oil fired reheating furnace is heating 8 Tonne material/hr from 50 0C to 1250 0C temp. Specific gravity of oil is 0.95 and C Vof oil is 9600 KJ/kg .Oil consumption is 725 lit/hr. Find efficiency of Furnace. Specific heat of material is 0.1 Kcal/kg/0C. (ક) એક ઓઇલ ફ યડા રીહીટીગ ભઠઠી દર કલ ક 8 ટન મટીરીયલન 50 0Cથી 1250 0C ત પમ ન સધી ગરમ કર છ. ઓઇલની સપ. ગરવીટી 0.95 અન કલોરીફીક વલય 9600 KJ/kg છ. ઓઇલ વપર શ 725 lit/hr છ તો ભઠઠીની ક યાકષમત શોધો. મટીરીયલની સપ. હીટ 0.1 Kcal/kg/0C લો.
[4 marks]Stock is charged through an open door of 700 mmX650mm size in an oil fired furnace. Furnace wall thickness is 375 mm and temperature is 1250 0C. Calculate energy loss by radiation through this open door. Also calculate this loss in term of excess oil to be used. C Vof oil is 9900 kcal/kg. Black body radiation is 30 kcal/cm2/hr at 1250 0C. Take emissivity as 0.8 and radiation factor 0.71. 2/4 (ક) એક ઓઇલ ફ યડા ભઠઠીન 700 mmX650mm મ પન ખલલ દરવ રજ િ ર સટોકન ગરમ કરવ મ આવ છ. ભઠઠીની દરદવ લની રજડ ઇ 375 mm અન ત પમ ન 1250 0C છ તો ખલલ દરવ રજ િ ર હીટ વયય શોધો. આ વયયન ઓઇલન વધ ર ન વપર શન રપમ શોધો. કલોરીફીક વલય 9900 KJ/kg છ. બલક બોડી રદરડયશન 30 kcal/cm2/hr, 12500C પર છ. એમીસીવીટી 0.8 અન રડીયશન ફકટર 0.71 છ.
Explain Pump up Method for finding Free Air Delivered. પરશન. ૪ (અ) ફરી એર ડીલીવર શોધવ મ ટની પમપપ અપ રીત સમરજવો.
[3 marks]Write and explain any five measures of energy saving of a compressor. (અ) કમપપરશર મ ટ ઉરજ ાબચ વની કોઇ પણ પ ાચ મ પન લખી સમરજવો
[3 marks]Find Corrected LMTD of shell and tube type heat exchanger having following data. Flow of hot and cold fluid are 719800 kg/hr and 881150 kg/hr respectively. Inlet and outlet temp. of hot fluid are 145 0C and 102 0C respectively. Inlet and outlet temp. of cold fluid are 25.5 0C and 49 0C resp. Consider one pass in shell side. (બ) શલ અન ટયબ હીટ એકષ ચજર ન કરકટડ LMTD નીચન મ હીતી પરથી શોધો. ગરમ અન ઠાડ ફલઇડનો ફલો રટ 719800 kg/hr અન 881150 kg/hr છ. ગરમ ફલઇડન અાદર જત અન બહ ર નીકળત ત પમ ન 145 0C અન 102 0C છ. ઠાડ ફલઇડન અાદર જત અન બહ ર નીકળત ત પમ ન 25.5 0C અન 49 0C છ. શલ મ એક પ સ લો.
[4 marks]Find free air delivery of the compressor. Receiver capacity = 35 m3, Final pressure = 7.5 kg/cm2 g, Temp. of compressed air = 55 0C, Amount of air stored in the system = 0.1 m3, Atm. Pressure = 1.026 kg/cm2 abs., Initial pressure = 0 kg/cm2 g, Initial air temp. = 30 0C, compressor pump-up time = 6 minute. (બ) કમપપરશરની ફરી એર ડીલીવર શોધો.(cid:13)રીસીવર કષમત 35 m3, ફ ઇનલ પરસર 7.5 kg/cm2 g, કમપપરશર એર ન ત પમ ન 55 0C, એર સટોરની વલય 0.1 m3 વ ત વરણ પરસર 1. 026 kg/cm2 abs, શરઆત ન પરસર 0 kg/cm2 g, શરઆતન હવ ન ત પમ ન ૩૦0C અન કમપપરશર પમપપ અપ સમય 6 શમનીટ .
[4 marks]Find thermal efficiency of an oil fired boiler by indirect method. 3/4 1. In ultimate analysis of oil following percent content are found C=84%, H =12%,O =1% and S=3%22 2. GCV of oil = 10200 kcal/kg. 3. Steam generation pressure = 7 kg/cm2. 4. Enthalpy of steam = 600 kcal/kg 5. Temp. of feed water = 60 0C 6. Percent oxygen in flue gas = 7%. 7. Percent CO in flue gas = 11%.2 8. Temp. of flue gas = 220 0C. 9. Atm. Temp. = 27 0C 10. Moisture in air = 0.018 kg/kg of air. (ક) ઓઇલ ફ યડા બોઇલરની પરતયકષ ક યાકષમત નીચ મજબની મ શહતી પરથી શોધો. C=84%, H =12%, O =1% and S=3%, ઓઇલની GCV = 10200 kcal/kg.,વર ળન ઉતપ દીત22 દબ ણ 7 kg/cm2,વર ળની એથ લપી = 600 kcal/kg.ભર ત પ ણીન ત પમ ન = 60 0C, ફલય ગસમ % O = 7%,ફલય ગસમ % CO = 11%,ફલય ગસન ત પમ ન = 22022 0C,વ ત વરણન ત પમ ન = 27 0C, હવ મ ભજ = 0.018 kg/kg of air.
External and Internal design condition in summer are (40 0C DBT and 27 0C WBT ) and (250C DBT and 50% RH ) respectively.. If ventilation air used is 70 m3/min, then calculate total load of outside air in kW. પરશન. ૫ (અ) ઉન ળ ની બ હય અન આતદરરક શરતો કરમ નસ ર(40 0C DBT અન 27 0C WBT) અન (250C DBT અન 50% RH ) આપલ છ. જો વનટીલશન હવ વપર શ 70 m3/min હોય તો બ હય હવ નો ટોટલ ભ ર kW મ શોધો.
[4 marks]Explain shading factor and external shading in context of heat gain through glass. (બ) શડીગ ફકટર અન બ હય શડીગ,ક ચમ થી પરસ ર થત ઉષમ વધ ર ન સાદભામ સમરજવો.
[4 marks]Write equation of Total Equivalent Temp. Difference with usual notation. (ક) TETD ન સમીકરણ લખી તન પદોનો અથા જણ વો.
[3 marks]Explain Flywheel effect of Building Material. (ડ) શબલડીગ સ મગરીની ફલ યવહીલ અસર સમરજવો. 4/4
[3 marks]An oil fired furnace has temp of 1250 0C and average oil consumption 475 litre/hr. Temp of flue gas, leaving the pre heater is 3000C. Sp. Gravity of oil is 0.9 and C Vis 9900kcal/kg. Average 13% Oin the flue gases. Sp. Heat of2 flue gas is 0.25 kcal/kg0C. Temp of atmospheric air is 450C and air fuel ratio can be taken as 15:1. Calculate total sensible heat loss, sensible heat loss/ hr and % sensible heat loss in terms of oil. (ડ) એક ઓઇલ ફ યડા ભઠઠીન ત પમ ન 1250 0C અન ઓઇલ વપર શ 475 litre/hr છ. પરીહીટર પછીન ફલય ગસન ત પમ ન 3000C છ. ઓઇલની સપ. ગરવીટી 0.9 અન કલોરીફીક વલય 9900 KJ/kg છ. ફલય ગસમ 13% O છ. ફલ ગસની સપ. હીટ 0.25 Kcal/kg/0C લો. વ ત વરણન2 ત પમ ન 450C અન એર ફયલ રશશયો 15:1 લો. ટોટલ સનસીબલ હીટ વયય, સનસીબલ હીટ વયય/કલ ક અન % સનસીબલ હીટ વયય શોધો.
[4 marks]Explain energy loss caused from outside surface and structure of the furnace. (ડ) ભઠઠીન બ હય સપ ટી અન બાધ રણન લીધ થતો ઉરજ ાવયય સમરજવો.
[4 marks]