Process Equipment Design -I — Winter 2019

Describe the situation if fluid velocity through circular pipe is beyond the recommended velocity range for a specified operating condition.

Explain in brief about the equivalent length of pipes and joints.

Acentrifugal pump is drawing water from an overhead tank, exposed to atmosphere. Vertical distance between free surface of liquid in the tank and centre line of the pump is 10 m. Capacity of centrifugal pump is 10000 kg/h. Maximum operating temperature is 50 °C. Vapor pressure of water at 50 °Cis 92.51 torr. Total length of suction pipe 10.5 m, having two 90 ° elbows. Material of pipe is carbon steel. Density of water = 1000 kg/m3, Viscosity of water = 0.558 cP. K- Value for 90ºelbow is 0.75. friction factor f = 0.0394 Re-0.16. For the velocity of water in suction line 1 m/s, Determine (1) The size of suction pipe (2) Total frictional pressure drop in suction line (3) (NPSH) of centrifugal pump. A

How baffle cut and baffle spacing affect tube outside heat transfer coefficient.

Determine the designation of the shell & tube heat exchanger based on following TEMA notations: 1. BEM 2. BFL 3. AKT 4. CFU

1-2 shell and tube heat exchanger is used to cool methanol condensate from 95 °C to 40°C. Flow rate of methanol is 100000 kg/h. Brackish water is used as coolant with temperature rise from 25 °Cto 40 °C. Property Methanol Brackish Water Heat Capacity, kJ/kg °C 2.84 4.2 Density, kg/m3 750 995 Viscosity, mN.s/m 0.34 0.8 Thermal conductivity, W/m °C 0.19 0.59 Choose 20mm od, 16 mm id, 4.88 m long cupro-nickle tubes with triangular pitch Pt = 1.25d . Based on overall heat transfer coefficient 600 W/m2C O Calculate (1) Number of tubes (2) Shell Diameter Kand n for tube bundle diameter: (For triangular pitch Pt= 1.25d ) 1 1 O No. of tube side passes 1 2 4 6 K 0.319 0.249 0.175 0.0743 0.03651 n 2.142 2.207 2.285 2.499 2.6751

Describe advantages and disadvantages of air cooled heat exchanger.

Describe functions of down comer & mention types of down comers.

Discuss in brief the factors affecting selection of tray type.

Acetic acid to be separated from a process stream containing 80% acetic acid and 20% water (by mass) by continuous distillation column at atmospheric pressure. Concentration of water in bottom product (pure acetic acid) should not be greater1 than 50 ppm. Top product (distillate) contains 80% water and 20% acetic acid (by mass). Feed is liquid at 30 °C. Estimate the number of theoretical stages required both graphically and empirically. Mole fraction of water in liquid, x Mole fraction of water in vapor, y 0.0 0.0 0.1881 0.3063 0.3084 0.4467 0.4498 0.5973 0.5195 0.6580 0.5824 0.7112 0.6750 0.7797 0.7261 0.8239 0.7951 0.8671 0.8556 0.9042 0.8787 0.9186 0.9134 0.9409 0.9578 0.9708 1.0 1.0 Take q= 1.272 & R = 2R m

Describe determination of minimum reflux ratio by McCabe-Thiele method.

Explain the method for checking liquid entrainment & weeping for sieve plate.

Acontinuous rectifying column handles a mixture consisting of 40 per cent of benzene by mass and 60 per cent of toluene at the rate of 4 kg/s and separates it into a product containing 97 per cent of benzene and a liquid containing 98 per cent toluene. The feed is liquid at its boiling-point.

How distribution coefficient affects liquid liquid extraction.

Classify industrially important extractors.

Explain process design of settler.

How to decide optimum solvent amount based on number of theoretical stages for liquid liquid extraction.

Discuss about various liquid distributors in detail.

Discuss about process design of venturi scrubber.

List out various equipments used as an absorber/ scrubber.

Discuss advantages of Falling film absorber over Packed tower type absorber.2

Sulphur dioxide is recovered from a smelter gas containing 3.5 per cent by volume of SO , by scrubbing it with water in a countercurrent absorption tower. The gas is2 fed into the bottom of the tower, and in the exit gas from the top the SO exerts a2 partial pressure of 1.14 kN/m2. The water fed to the top of the tower is free from SO , and the exit liquor from the base contains 0.001145 kmol SO /kmol water.22 The process takes place at 293 K, at which the vapour pressure of water is 2.3 kN/m2. The water flow rate is 0.43 kmol/s. If the area of the tower is 1.85 m2 and the overall coefficient of absorption for these conditions K” a is 0.19 kmol SO /sm3 (kmol of SO /kmol H O), what is the height L 2 2 of the column required? The equilibrium data for SO and water at 293 Kare:2 kmol SO /1000 kmol H O 0.056 0.14 0.28 0.42 0.56 0.84 1.40522 kmol SO /1000 kmol Inert gas 0.7 1.6 4.3 7.9 11.6 19.4 35.32

Differentiate Random and Regular packing.

Discuss about how to select the solvent flowrate for absorption operation.